Get in Touch
  1. Home
  2. > Blog
  3. > Blog Detail

What guards should be on a jaw crusher

Jaw Crusher Guard Plate of the moving plate and static E side of the board there are two guards, many customers will ask these two shields can not, because they think this will increase the cost of the machine, but also for the late machine Maintenance to increase the cost of spending, but the ancients said, sharpening the workers do not

  • Inspection precautions for each part of jaw crusher
    Inspection precautions for each part of jaw crusher

    Aug 28, 2019 Aug 28, 2019 Third, Side guard plate and jaw plate: Check whether the side guard plate and the jaw plate are composed of the movable jaw body with impact resistance and high stability. In addition, the side guard plate is complicated to manufacture and is prone to omission, before the purchase. The side guards should be inspected for properness

    Get Price
  • What are the wearing parts of the jaw crusher?-Jiaozuo
    What are the wearing parts of the jaw crusher?-Jiaozuo

    Feb 15, 2019 Feb 15, 2019 The jaw crusher wearing parts include fixed jaws, movable jaws, springs, brackets, crushing plates, guard plates, etc. Among them, the jaw plates, the toggle plates and the crushing plates are the * seriously damaged parts of the jaw crusher. The jaw plate is the * expensive component in the jaw crusher. The quality of the crusher is actually

    Get Price
  • How effective maintenance of jaw crusher?
    How effective maintenance of jaw crusher?

    Jaw crusher maintenance mainly from the following three aspects: Before starting maintenance 1, should carefully check bearing lubrication condition is good, the bearing bracket connections have enough grease. 2, you should carefully check all fasteners are fully tightened. 3, guards are good, found to be unsafe, should immediately remove it

    Get Price
  • How to Properly Install and Use Jaw Crusher | HXJQ
    How to Properly Install and Use Jaw Crusher | HXJQ

    Jun 01, 2019 Jun 01, 2019 On installation: installation of components of jaw crusher. Next, we will learn about the installation of jaw crusher from the parts of the frame, eccentric shaft and bearings, rod bolts, brackets, movable jaw plate, and dental plates. 1.The installation of the frame. The jaw crusher is installed on the concrete foundation

    Get Price
  • JAW CRUSHER Model 3352 Spec Sheet
    JAW CRUSHER Model 3352 Spec Sheet

    JAW CRUSHER Model 3352 Spec Sheet ... This equipment should not be operated without all guards attached in their normal position. Placement of guards and oth er safety equipment is often dependent upon the area and how the product is used. A safety study should be made by the user of the application, and, if required additional

    Get Price
  • what speed / rpm jaw crushers should do
    what speed / rpm jaw crushers should do

    rpm for jaw crusher--Henan Mining Heavy Machinery Co., Ltd. what speed rpm jaw crushers should do. Focus on Crushers - Rock To Road. While the machine has a 600 hp motor, the crusher

    Get Price
  • Jaw Crusher - an overview | ScienceDirect Topics
    Jaw Crusher - an overview | ScienceDirect Topics

    For a jaw crusher the thickness of the largest particle should not normally exceed 80–85% of the gape. Assuming in this case the largest particle to be crushed is 85% of the gape, then the gape of the crusher should be = 45.7/0.85 = 53.6 cm and for a shape factor of 1.7, the width should be = 45.7 1.7 = 78 cm

    Get Price
  • Guidelines for Management Crushing and Screening
    Guidelines for Management Crushing and Screening

    should never be used on or near a crusher while it is running. Before any barring begins, the plant should be shut down and locked out. D. Unstable material that could fall causing injury must be cleared away or made safe. The operator should select a bar that is a suitable length for the job and be positioned so as not lose balance

    Get Price
  • Jaw Crushers Support | McLanahan
    Jaw Crushers Support | McLanahan

    Over time, a wet bead or line of grease should be seen between the labyrinth seal and the bearing housing. When your Jaw Crusher is new, use Mobilux EP2 for temperatures above 30 F and Mobilux EP1 for temperatures below 30 F. When using an automatic greaser, use Mobilux EP1 for temperatures above 30 F and Mobilux EP0 for temperatures below

    Get Price
  • JAW CRUSHER Model 3144 Spec Sheet
    JAW CRUSHER Model 3144 Spec Sheet

    JAW CRUSHER Model 3144 Spec Sheet ... This equipment should not be operated without all guards attached in their normal position. Placement of guards and oth er safety equipment is often dependent upon the area and how the product is used. A safety study should be made by the user of the application, and, if required additional

    Get Price
  • Cause Analysis and Problems Solving of Jaw Crusher | HXJQ
    Cause Analysis and Problems Solving of Jaw Crusher | HXJQ

    Dec 10, 2019 The jaw crusher is mainly composed of a frame, a movable jaw assembly, a movable jaw, a fixed jaw, a triangular wheel, a flywheel, a bracket, a side guard, a discharge port adjusting device and a driving device

    Get Price
  • Choosing the correct jaw profile for your crusher - Bucket
    Choosing the correct jaw profile for your crusher - Bucket

    Mar 20, 2021 Mar 20, 2021 Choosing the correct jaw profile for your crusher Choosing the most appropriate profile is not simple and there are no rules, since each application has a number of different variables like feeding, opening, product needs and problems. Certain profile types decrease or increase the crusher’s hourly production. So, for the correct choice, it is necessary […]

    Get Price
CONTACT US

Are You Looking for A Consultant?

toTop
Click avatar to contact us